Dome E2c DisplayUser’s Guide

Also included: Composite video, S-video, and VGA cablesAMLCD panel mounted on desk standDisplay controllerDC power adapter Power cordsDVI cableQuick r

About the DisplayThe Dome E2c display system offers a 541-mm (21.3-in) color UXGA 1200x1600 AMLCD unit with a luminance output of 500 nits minimum. Th

2 | Dome E2c DisplayDisplay ComponentsReview this illustration of the back panel to identify controls and ports on the display unit.Legend1 Reset.

About the Display | 3Display PositionsYou can adjust the tilt, height, viewing angle, and orientation of the display to maintain an ergonomic and

4 | Dome E2c DisplayDesk Stand FeaturesUnfasten the stand lock to adjust display height. Remove the stand cover to thread the power cord and DVI c

Installing the Display | 5Installing the DisplayBefore you install the display controller, remove any existing graphics card and its driver from y

6 | Dome E2c Display Install the Display ControllerBefore you install the AX1 display controller, make sure your display system will be set up in

Installing the Display | 7Connect the Video and Power CablesUse only the power adapter (Ault MW122KA1223F52), power cord, and the video cable ship

8 | Dome E2c DisplayInstall the Display DriverUpon restarting your computer system, you must log on with administrator privileges. On Windows 2000

Installing the Display | 9Adjust Display PropertiesUse the Display Properties dialog to make changes to the video settings or to set up a dual-dis

© 2006 Planar Systems, Inc. All rights reserved.Information in this document has been carefully checked for accuracy; however, no guarantee is given t

10 | Dome E2c DisplayAppendixTroubleshootingDome E2c SpecificationVideo ModesVideo TimingConnector PortsLED Status LightsComponent RemovalPower Ma

Troubleshooting | 11TroubleshootingProblem Possible Cause SolutionNo image appears on the screenComputer is not powered on.Turn on computer.Power

12 | Dome E2c DisplayDome E2c SpecificationIn locations where 240V outlets are used, connect the Dome E2c display only to a center-tapped, 240V, s

Dome E2c Specification | 13Power SupplyCAUTION: Use only the power adapter supplied with the Dome E2c display unit; Ault MW122KA1223F52. Reliabil

14 | Dome E2c DisplayVideo ModesResolutions expressed in pixels (W x H). Single desktop requires dual displays. Video TimingDisplay Resolution O

Connector Ports | 15Connector PortsThe video signal connector is a standard DVI connector, driving data to the display. Diagnosis requiring DICOM

16 | Dome E2c DisplayLED Indication LightsThe LED indicator on the connector plate provides information on the display status.Reset (left) and LED

Display Driver Removal | 17Display Driver RemovalFollow the appropriate procedure below to remove the AX1 driver from your system.To remove the AX

18 | Dome E2c DisplayPower ManagementYou have two ways to lower energy usage when the Dome E2c display is idle:• Dome CXtra Backlight Saver servic

19IndexBbrightness, display 9Ccleaning viiiconfiguration, dual setup 9connectingDVI cable 7power cord 7connector port 15contents, package xDdesk stand

iiiContentsProduct Information ivAbout the Display 1Installing the Display 5Appendix 10Index 19Regulatory Compliance 20S

Regulatory ComplianceCanada, European Union, United StatesThis display has been tested and found to comply with IEC/EN 60601-1 and IEC/EN 60601-1-2 st

The applicable safety standards for an MDD Class I display are IEC/EN 60601-1:1990 along with Amendments 1 and 2. To help the medical device designer

EU Declaration of Conformity for Medical ApplicationA Declaration of Conformity has been filed for this product. For additional copies of the Declarat

U.S. FCC Compliance StatementThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device

AustralianChina JapanKoreaC-Tick Australian Communications Authority regulating product EMC compliance. CCC China Compulsory Certification regulating

Standard WarrantySummary• Standard 1-year “repair and return” warranty• A 2-year backlight warranty on color displays*• Typical repair turnaround time

Summary Limitations and Exclusions of Dome Displays1 Customer must provide original proof of purchase of the display system.2 Warranty is void on any

Exclusion of DamagesTHE LIABILITY OF PLANAR IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. PLANAR SHALL NOT BE LIABLE FOR THE FOLLOWI

America SalesPlanar Systems, Inc. 1195 NW Compton Drive Beaverton, OR 97006-1992 USA (503) 748-1100 phone(503) 748-1493 faxMedical SalesPlanar Systems

iv | Dome E2c DisplayProduct InformationThe design of the Dome E2c digital display takes into account every known measure to ensure your personal

Product Information | vSymbol explanationsIntended useThe Dome E2c display is an AMLCD display designed for viewing medical X-ray images. This unit

vi | Dome E2c DisplaySafety precautionsExternal equipment intended for connection to signal input, signal output, or other connectors, must comply

Product Information | viiUnpacking and handling tipsThe Dome E2c display is a precision instrument that requires proper care to maintain product ope

viii | Dome E2c DisplayCleaning the displayObserve the following guidelines to maintain the display and the LCD screen.• Use a clean, lint-free, a

Product Information | ixShipping/storing the displayKeep the display in its shipping container until installation. Return the display to its origina